Electronic Engineering, Analog and RF integrated circuit design

From 46.45 £ /h

From basic principles to advanced topics in the field of analog & RF integrated circuit design are presented. As an integrated circuit designer working in the industry for more than 10 years and experiencing a dozen of successful tape-outs in various CMOS and III-V fabrication technologies, I'm passionate to share my knowledge with university students who are seeking to enrich their comprehension of IC-related studies and courses.

Location

Use Ctrl + wheel to zoom!

At student's location :

Around Leuven, Belgium

Around Antwerp, Belgium

Around Ixelles-Elsene, Belgium

About Me

Mohammad Hossein is currently with Pharrowtech company, Leuven, Belgium, working as an RFIC system design engineer. His major fields of interest are design and implementation of RF, microwave, and mmWave integrated circuits including LNAs, power amplifiers, phase-shifters and, true-time delay circuitry, non-linear circuits such as mixers, phased array systems, and planar electromganetic waveguides.

Education

He received the B.Sc. degree in microwave engineering from Shahed university, Tehran, Iran, in 2011, the M.Sc. degree in electronic engineering from K. N. Toosi University of Technology, Tehran, Iran, in 2014, and the Ph.D. degree in electronic engineering from Sharif university of technology, Tehran, Iran, in 2020.

Experience / Qualifications

Analog IC / Embedded System Engineer at Sparnex company
• Design of analog front-end and line-driver chips
• PCBdesign of chip evaluation boards
• Firmware development of wire-linked devices
• Test and measurement with evaluation boards

RFIC System Design / Embedded System Engineer at PharrowTech company
• Performance evaluation and enhancement of 60 GHz transceiver chips
• Link budget analysis of communication systems
• Firmware development for chip application features (C++/Python)
• Test and measurement of 60 GHz transceiver chips

Integrated Circuit Designer at TFMchip IC-design group
• System-level design of RX/TX chip operating at 16 GHz for 5G applications
• Design of CMOS LNA block operating at 16 GHz
• Design of 6-bit CMOS phase-shifter chain operating at 16GHz
• Innovation of three novel wideband time-delay control circuits implemented in CMOS technology
• Design of GaN passive mixer with high linearity at 8 GHz

Age

Adults (18-64 years old)

Student level

Beginner

Intermediate

Advanced

Duration

60 minutes

The class is taught in

English

Skills

Electronic circuits

Telecommunications

Availability of a typical week

(GMT -05:00)

New York

At student's home

Mon

Tue

Wed

Thu

Fri

Sat

Sun

00-04

04-08

08-12

12-16

16-20

20-24

Tresor

4.63

(8)

. Civil engineer, holder of numerous network certifications (CCNA, CCNP, CCDP, CICA, CICE, F5), accompanies and supervises students or professionals wishing to obtain their CCNA certification.
This course is designed specifically for CCNA applicants and anyone interested in understanding and administering a medium-sized network.
This course includes several modules namely:
- general knowledge of network services
- understanding and configuration of the switches
- Understanding and configuring routers
-understanding WAN (Wide Area Network) networks

4.63

(8)

Hello, I am a doctoral student in electrical engineering and associate professor in engineering sciences, experienced in the field of electrical engineering, I offer support courses in the subjects of engineering sciences (Electronics, automatics, electrical engineering, automation, programming).

Digital electronics
Analog electronic
electromagnetism (propagation of high frequency waves)
Automatic (continuous, sampled)
electrical engineering (transformers, electrical machines, switching power supply)
C / c ++ programming, Assembler, ARM, STM32
renewable energy (wind, PV)
engineering Sciences
RDM
Python,VHDL
PIC Microprocessor and Microcontroller
Signal processing and data acquisition
Engineering Sciences

These courses allow the student to get up to speed and regain confidence in all scientific subjects, just as they prepare him effectively for the Baccalaureate, the Preparatory Classes or various examinations of the engineering classes.

COURSE OBJECTIVES AND PEDAGOGICAL APPROACH

Resumption and deepening of fundamental concepts through exercises with course reminders.

Put the student in a situation of questioning and research.

Respond to individual issues and questions

Exercise training in order to achieve real mastery of the content.

Learn to build theoretical reasoning from observable facts or hypotheses.

Specific preparation for higher education requirements (in-depth content, increase in work capacity, enrichment of scientific background)

This educational approach is effective since it has often led me to interesting results with my students.

Associate professor provides support courses in electrical engineering

Sam

4.63

(8)

Professor in mathematics, computer science at HEFF in Brussels and before a professor of electronics at the IEPSCF, ENGINEER in electronics ECAMIEN graduated in mathematics-physics and I propose an individualized pedagogy, an aid in the preparation of the interrogations or exams. My goal is to advance the student without overloading him. I give homework after each lesson and periodically provide progress reports.
I strongly encourage the student because the state of mind and morale have a direct influence on school results.
I am someone understandable and I always try to take each in his own way.
I always start by clarifying the course after giving an example then giving an example to the student plus doing a full exercise and finally correcting an exam together generally this is methodology but it can change from one case to another revise the courses studied in class.
give remarks that makes the job easier. give the tips and tricks you need to get a good rating.
try to make the student quick in these calculations and demonstrations
and give the way in which he should manage his duty

Marko

4.63

(8)

✅ Experienced teacher offering private online physics lessons for all levels.
✅ Fully dedicated and focused on student progress.
✅ Very patient, systematic, and organized.

I teach a wide range of topics in physics, including but not limited to:

5- Physical quantities and units
- Kinematics (types of motion, kinematics of point particles and rigid bodies)
- Dynamics (frictional and inertial forces, Newton's laws)
- Laws of conservation (energy, momentum)
- Theory of collision processes
- Inertial and non-inertial reference frames
- Potential and kinetic energy
- Gravitation and gravity fields
- Oscillatory and wave motions
- Harmonic oscillator
- Doppler effect
- Standing waves
- Sound waves and physical characteristics of sound
- Surface tension and capillary phenomena
- Fluid mechanics
- Temperature and heat
- Calorimetry
- Phase transitions
- Principles of thermodynamics
- Electrostatics
- Electromagnetism
- Kirchhoff's laws
- Electronic circuits
- Dielectrics
- Optics
... and much more.

If there are specific topics you would like to focus on or if you have any questions, feel free to let me know. I am here to help you deepen your understanding of physics.

Loris

4.63

(8)

My lessons are specifically designed for students who need extra support in technical subjects such as math, physics, programming and related subjects. Whether you are struggling with basic concepts, need extra help preparing for tests or want to understand complex topics, I am here to help you on your way. Tutoring is preferably done online, I have an ipad so lessons run smoothly.

Youssef

4.63

(8)

Hello, I am a doctoral student in electrical engineering and associate professor in engineering sciences, experienced in the field of electrical engineering, I offer for students of preparatory classes and technical high school support courses in the subjects of engineering sciences (Electronics, automatic, electrical engineering, automation, programming).

Digital electronics
Analog electronic
electromagnetism
Automatic
electrical engineering (transformers, electrical machines, switching power supply)
C / c ++ programming, Assembler, ARM, STM32
renewable energy (wind, PV)
engineering Sciences
RDM
Python
PIC microcontroller
Microprocessor

These courses allow the student to get back to level and regain confidence in all scientific subjects, as well as effectively preparing him for the Baccalaureate, Preparatory Classes or various exams.

COURSE OBJECTIVES AND PEDAGOGICAL APPROACH

Resumption and deepening of fundamental concepts through exercises with course reminders.

Put the student in a situation of questioning and research.

Respond to individual issues and questions

Exercise training in order to achieve real mastery of the content.

Learn to build theoretical reasoning from observable facts or hypotheses.

Specific preparation for higher education requirements (in-depth content, increase in work capacity, enrichment of scientific background)

This educational approach is effective since it has often led me to interesting results with my students.

Associate professor provides support courses in electrical engineering

Amine

4.63

(8)

The course is based on the understanding of electricity in general, but can deviate as well towards electronics as towards mechanics.

I am a student in the 3rd year of a bachelor's degree in polytechnic, civil engineer. I can give lessons for everyone, at any level and for all ages.

Pawan

4.63

(8)

Mathematics, programming skills, and telecommunications are the core subjects of my expertise. I firmly believe that everyone has the potential to excel in any field. While some may grasp concepts easily, others may need initial guidance to get started. Many students face challenges that can be overcome with proper guidance and specialized tips from experts.

With my Ph.D. in Engineering (Telecommunication) and over 5 years of experience as a programmer, I am confident in my ability to motivate and guide young people to succeed in Mathematics, Programming, and the basics of telecommunications.

Freddy

4.63

(8)

Based on a project to be agreed upon, create, produce and program an Arduino to achieve the initial objective.
Example projects:
- Drilling, milling, cutting table
- robotization of a vehicle (truck, crane, various)
- Carrying out various processes.

Good-fit Instructor Guarantee

Contact Mohammad